IPS E-LOC Transition Couplings | IPS to IPS Conduit Reducers
IPS E-LOC Transition Couplings — Product Overview
IPS E-LOC Transition Couplings join two IPS conduits of different sizes, such as 2" x 1" or 4" x 3". The E-LOC is a compression coupling: a PVC sleeve with a polyurethane elastomer sealing liner that grips each conduit end and makes a watertight, airtight joint in buried or restrained runs, without solvent cement, primer or heat.
It joins dissimilar materials, including PVC, HDPE, fiberglass and metal conduit, and is watertight to 200 psi when restrained on smooth wall, ribbed and corrugated duct. 12" long versions give more engagement where conduit ends are cut short or misaligned.
Key Features
- Twenty-three IPS to IPS transitions: from 1" x 3/4" through 6" x 5", including 12" long 5" x 4" and 6" x 5" versions.
- Compression seal: the polyurethane elastomer liner seals watertight and airtight, rated to 200 psi when restrained.
- Joins dissimilar materials: PVC, HDPE, fiberglass or metal conduit.
- No cement, primer or heat: seat it with a board and mallet, or a bar and block on larger sizes.
- Rated sleeve: PVC sleeve stock meets NEMA TC2, TC6 and TC8 and ASTM F-512, rated to 90°C.
- Specialty duct sizes: for C-duct, 2" EMT, Canadian DB, corrugated, ribbed, 40 mm and other non-IPS duct, see Specialty Duct E-LOC Transition Couplings LINK.
How to Read the Part Number
ETCO part numbers encode the two outside diameters in thousandths of an inch. ELA-237131 is 2.375" (2" IPS) to 1.315" (1" IPS). A trailing -12 is the coupling length in inches.
IPS O.D. Chart
| O.D. (IN.) | Nominal Size |
|---|---|
| 0.840" | 1/2" IPS |
| 1.050" | 3/4" IPS |
| 1.315" | 1" IPS |
| 1.660" | 1-1/4" IPS |
| 1.900" | 1-1/2" IPS |
| 2.375" | 2" IPS |
| 2.875" | 2-1/2" IPS |
| 3.500" | 3" IPS |
| 4.000" | 3-1/2" IPS |
| 4.500" | 4" IPS |
| 5.563" | 5" IPS |
| 6.625" | 6" IPS |
Installation
- Check the size: Confirm the coupling matches the conduit outside diameters; E-LOC sizes are based on standard O.D.
- Clean the ends: Wipe the conduit ends clean of burrs, dirt and debris.
- Mark the depth: Mark each conduit at half the coupling length from its end. When fully seated, the mark sits at the coupling edge.
- Lubricate: Lubricate with water, or water with a little dish soap. Do not use motor oil, thread lubricant or WD-40 type products.
- Seat the coupling: Install the larger conduit end first where possible. Seat with a board across the end and a mallet on small sizes, or a bar and block on large sizes. Never strike the coupling directly.
- Restrain the run: Bury or restrain the run; the 200 psi watertight rating applies when restrained.
Available Sizes & Specifications
| Part No. | From (O.D. - IN.) | To (O.D. - IN.) | Length / Style | Min. Order Qty |
|---|---|---|---|---|
| ELA-131105 | 1.315 | 1.050 | Std. | 25 |
| ELA-166105 | 1.660 | 1.050 | Std. | 15 |
| ELA-166131 | 1.660 | 1.315 | Std. | 15 |
| ELA-190105 | 1.900 | 1.050 | Std. | 15 |
| ELA-190131 | 1.900 | 1.315 | Std. | 15 |
| ELA-190166 | 1.900 | 1.660 | Std. | 15 |
| ELA-237131 | 2.375 | 1.315 | Std. | 10 |
| ELA-237166 | 2.375 | 1.660 | Std. | 1 |
| ELA-237190 | 2.375 | 1.900 | Std. | 15 |
| ELA-287237 | 2.875 | 2.375 | Std. | 9 |
| ELA-350190 | 3.500 | 1.900 | Std. | 8 |
| ELA-350237 | 3.500 | 2.375 | Std. | 8 |
| ELA-350287 | 3.500 | 2.875 | Std. | 9 |
| ELA-450237 | 4.500 | 2.375 | Std. | 6 |
| ELA-450287 | 4.500 | 2.875 | Std. | 6 |
| ELA-450350 | 4.500 | 3.500 | Std. | 7 |
| ELA-450400 | 4.500 | 4.000 | Std. | 7 |
| ELA-556350 | 5.563 | 3.500 | Std. | 5 |
| ELA-556450 | 5.563 | 4.500 | Std. | 6 |
| ELA-556450-12 | 5.563 | 4.500 | 12" | 1 |
| ELA-662450 | 6.625 | 4.500 | Std. | 4 |
| ELA-662556 | 6.625 | 5.563 | Std. | 4 |
| ELA-662556-12 | 6.625 | 5.563 | 12" | 1 |
Each size carries its own minimum order quantity, shown in the table and pre-filled in the quantity box; any quantity at or above the minimum is fine. ETCO publishes additional sizes and lengths not listed here. Need one, or a combination you do not see? Call (815) 337-8845.

